|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used in the back of corner, pile guide, leg holder or a connector hinge to reduce stress from bolts.
|
These caps offer protection and finish to your leg piles.
|
Black powder-coated. 3 in.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Multinautic Dock Cleat, Dimensions: 6 in L, Nylon, Black, Includes: #12 x 3 in Bolts
|
Hot dipped galvanized joist. 2-3/4 in x 5 in x 1/8 in.
|
Multinautic 10000 Spare Pin, 1/2 in, Galvanized Steel, Industrial Grade, Suitable for: 10004 and 11003 Dock Hinges
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Multinautic 13300 Spare Pin, 3/4 in, Steel, Suitable for: #10007, #13303 or to Attach #13309, #13310 Dock Hinges
|
Multinautic Ring and Lag Screw, Dimensions: 2.5 in Dia, Stainless Steel
|
Galvanized steel cleat. 8 in.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pre-spliced, double-braided marine-grade dock line. For boats up to 20 ft.
|
Pre-spliced, double-braided marine-grade dock line. For boats up to 20 ft.
|
2 in x 20 ft strap. 1,300 maximum lb working load. Bolt and hook included.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Multinautic 10000 Inside Corner, Mounting Hole Size: 7/16 x 3/4 in, Dimensions: 6 in L x 5 in W x 1/8 in Thick, Galvanized, Suitable for: Stationary Dock with #10003 or #10010 Back Plate
|
6 in x 6 in galvanized base plate. Foot for pile to prevent sinking.
|
Connector hinge with 1/2 in pin. Galvanized steel.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 in flip-up cleat. Cast aluminum.
|
6 in flip-up cleat. Cast aluminum.
|
Hot dipped galvanized hinge. 3-1/2 in x 5 in x 3/16 in.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Leg holder for dock 5 in x 5 in. Used to hold dock leg pile up to 1-7/8 in Dia.
|
Multinautic 13300 Inside Corner, Mounting Hole Size: 9/16 x 1 in, Dimensions: 6 in L x 5 in W x 1/4 in Thick, Galvanized, Suitable for: Floating Dock with 13300-03 or 13300-04 Back Plate
|
Protects the side and top of the dock with 1-1/4 in cushion above dock level. Solid flaps attach easily to any dock. Excellent cushioning protects boat and dock from each other. Color is permanently molded into the vinyl and will not transfer to the hull.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit includes galvanized brackets, shaft, 8 in black rubber keel roller for ramps and trailers.
|
Use to support a stationary dock or a gangway. Maintain floating docks in position with multi-anchoring leg holders used as pile guides. 1-11/16 in OD.
|
To be installed on leg pile to protect boats against impacts. Post bumpers are great protection for pipe supported type docks. Protects the boat from contact with the metal dock pipe and hardware at dock level. Easily fits over 2 in OD dock pipe and rests securely against the dock. Has an inflation valve to adjust firmness.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Industrial, heavy-duty gauge 5 in x 5 in x 1/4 in. Used to connect two floating docks together.
|
Rated 1,300 lb. For trailers and ramps. High-performance gear system. Durable zinc finish. Two-way ratchet.
|
Stainless steel bolts and nuts with special "T" shape head. Pack of 2.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 in Dia wheel kit. Use to build a boat ramp, includes four 5 in wheels, two mounting brackets and axles. 2000 lb capacity.
|
Turns a ladder into a flip-up one to easily remove from water when needed. Design to fit on 15513 & 15524 Multinautic? four-step tubular dock ladders. May be adapted to other ladders but they will need some adjustments.
|
With its 22 deg angle, they stay away from boat hull. Their high profile is designed to be used on many dock line sizes and facilitates mooring. Slides ideally in the Uni-track system using T-bolts. 8 in (two holes).
|
|
|
